D
For short people with long arms and neck
I received my Miza a couple of days ago and now I wished I would have read the other reviews more thoroughly. I'm using it for my home studio with lot's of rack gear, effects and synths. My main MIDI keyboard I use with the table is Arturia Keylab 88 MkII.
First the good things:
Table looks good and feels fine
Assembly instructions were very good
I could build it alone but it helps if you have other person at least on the last step helping you. It is also quite heavy so prepare for lifting when the package arrives.
Racks are nice and even rack screws are included.
Lot's of room on the tabletop and lot's of height available for keyboard.
Then the bad stuff:
I'm not sure if this is actually good design as Zaor tries to sell it. I'm not even sure that have anyone even tested this after 3D CAD drawing since it has clear problems detected instantly if used and stated on the other reviews as well.
The keyboard drawer is at least 3-5cm too low. This might not sound much, but you have to have very low chair to fit your legs under it and play it comfortably. There is plenty of height available for your keyboard though, maybe even too much.
The tabletop is set too high. You will have serious ergonomy problems if you have mouse and keyboard on this table and at the same time try to stay low for the keyboard. The display will also be too high for this position.
Tabletop is also very deep, so if you have keyboard tray open it's almost impossible to reach the rack gear without moving the tray back or get standing. Of course this means that you have lot's of room for equipment on the table if that is what you are looking for.
I'm planning to fix keyboard height issues buy purchasing different set of wheels and moving the rails up a few cm, wish Zaor would have done this instead of DIY solution though.
Summary:
It could have been an awesome table, but with these "small" design flaws it's not so fun to use. So Zaor if you are reading this here's some suggestions:
- get tabletop down a couple of centimeters
- get keyboard level up a couple of centimeters
- shorten the tabletop a few centimeters
- test the product on real people and equipment after modeling it
First the good things:
Table looks good and feels fine
Assembly instructions were very good
I could build it alone but it helps if you have other person at least on the last step helping you. It is also quite heavy so prepare for lifting when the package arrives.
Racks are nice and even rack screws are included.
Lot's of room on the tabletop and lot's of height available for keyboard.
Then the bad stuff:
I'm not sure if this is actually good design as Zaor tries to sell it. I'm not even sure that have anyone even tested this after 3D CAD drawing since it has clear problems detected instantly if used and stated on the other reviews as well.
The keyboard drawer is at least 3-5cm too low. This might not sound much, but you have to have very low chair to fit your legs under it and play it comfortably. There is plenty of height available for your keyboard though, maybe even too much.
The tabletop is set too high. You will have serious ergonomy problems if you have mouse and keyboard on this table and at the same time try to stay low for the keyboard. The display will also be too high for this position.
Tabletop is also very deep, so if you have keyboard tray open it's almost impossible to reach the rack gear without moving the tray back or get standing. Of course this means that you have lot's of room for equipment on the table if that is what you are looking for.
I'm planning to fix keyboard height issues buy purchasing different set of wheels and moving the rails up a few cm, wish Zaor would have done this instead of DIY solution though.
Summary:
It could have been an awesome table, but with these "small" design flaws it's not so fun to use. So Zaor if you are reading this here's some suggestions:
- get tabletop down a couple of centimeters
- get keyboard level up a couple of centimeters
- shorten the tabletop a few centimeters
- test the product on real people and equipment after modeling it
0
0
Raportoi ongelmasta